Arduino Mega 2560

The Arduino Mega 2560 is a development board designed for building larger applications compared to other Arduino boards. The board is based on the ATmega2560 microcontroller operating at 16 MHz. It features 54 digital input/output pins (of which 15 are PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a USB connection, a power jack, an ICSP header, and a reset button.

SKU7002 14 900 CFA

16x2 Blue Backlit LCD

• This screen is an electronic device used to display data and messages. It is known as a 16x2 LCD screen. As its name suggests, it has 16 columns and 2 rows so it can display 32 characters (16 x 2 = 32) in total and each character will be composed of 5 x 8 (40) pixel points. Thus, the total number of pixels of this LCD screen can be calculated as follows: 32 x 40, or 1280 pixels. The color of the characters is white and the screen has a blue background. This also makes it readable in the dark.

SKU7036 2 310 CFA

20cm female-female jumper

This female-female jumper cable set will allow you to easily interconnect your breadboards, electronic boards and other components. You can also detach one or more cables depending on your needs. The cable has a female end at each extremity and requires no soldering.

SKU7043 35 CFA

1K Ohm - 1 Watt Resistor

1K Ohm - 1 Watt Resistor

SKU7237 40 CFA

Support for ATmega328

The ATmega328P is a low-power 8-bit CMOS microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega328P achieves speeds approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed.

SKU7298 144 CFA

28BYJ-48 stepper motor

4-winding unipolar stepper motor with gearbox and driver based on an ULN2003A allowing direct control of the motor with a microcontroller (e.g., Arduino) without a power interface for various applications such as office equipment, robotics, automation, etc.

SKU8016 2 220 CFA

Push button R13-507

Push button R13-507

SKU9036 223 CFA

GSM Module SIM800L (red)

The SIM800L GSM module is a mini module that provides 2G GSM and GPRS data. It is small and low-power. Twice the size of a coin and the working current in sleep mode is 1 mA. It uses a serial communication interface, supports advanced AT commands 3GPP TS 27.007, 27.005 and SIMCOM. It also supports A-GPS technology, which helps maintain the internal position of the cellular network. Compatible with Arduino Uno, Arduino Mini, Raspberry Pi. A mini GSM antenna is included, but an external power supply is required.

SKU9041 5 400 CFA

LM2596 HV DC-DC Converter

This DC-DC module is a step-down converter; the output voltage is lower than the input voltage.

This voltage regulator can lower an input voltage of up to 60V down to 3V with a 92% efficiency and 3A peak current.

The output voltage is adjustable via a multi-turn potentiometer on the module.

SKU107598 1 060 CFA

Raspberry Pi Pico W

The Raspberry Pi Pico W is a wireless version of the Raspberry Pi Pico. It offers the same features as the standard Raspberry Pi Pico, but with added Wi-Fi and Bluetooth support. It incorporates Infineon's CYW43439 chip, a single-band 2.4GHz wireless interface supporting IEEE 802.11 b/g/n wireless LAN. This allows for convenient wireless connection with other devices and networks.

SKU107597 9 980 CFA

CR2032 battery

CR2032 battery

SKU107596 300 CFA

16-channel 12V relay module

The 16-channel 12V relay module is a device that allows controlling high-power electrical loads from low-power signals originating from microcontrollers or other logic circuits.

SKU107595 8 450 CFA

18650 Li-ion 2S 20A battery protection PCB

The 18650 protection board for 4S 100A Li-ion battery is an electronic module designed to protect and ensure the safety of 18650 Li-ion batteries in a two-cell series configuration (2S).

SKU107594 800 CFA

Red laser pointer

Red laser pointer

SKU107593 2 500 CFA

TIP41

TIP41

SKU107592 290 CFA

NPN Transistor 2N5551

Transistor NPN 2N5551

SKU107591 25 CFA